Free Software Upgrades for Legacy/Older Products
Software upgrades are free for the life of the product.
DataRay has a policy of continuous product & software improvement. Monitor this page for the latest upgrades.

DataRay Software Licence Agreement. The download, installation &/or use of the program(s) on this site, implies your acceptance of the DataRay Software Licence Agreement. PDF format version of the Agreement

Suggestion: When upgrading the software, first open Windows Explorer and rename the old c:\Program files\DataRay directory with its Version number as, e.g. c:\Program files\DataRay500S8.
Then install the new software. If problems arise you can return to the old version.

Link to: Minimum PC Requirements
Link to: Upgrade Procedure if you are unsure.
Link to: Windows Compatibility

Legacy/Older Products

DOWNLOAD SOFTWARE
Full versions
 Posted

WinCamD-UCM large case (4.5" wide)
6.00P2 is the most recent working software for the Rev. 2 firmware originally installed on these cameras.
Use with current software, 6.00S4 and later, requires factory installed Rev.3 firmware. The firmware upgrade is free, but the customer pays shipping both ways.
[The sensor manufacturer changed their process after the large case -UCM's were manufactured, affecting offset trimming and calibration. Current software is compatible with the later chips, but requires Firmware Rev. 3 to work with the earlier chips.]

* BeamScope-P5 (retired in 2002) does not work with BeamScope-P7, P7U, P8 software.

** WinCam-PCI series products (retired in 2001) do not work with WinCamD software.
Upgrading from WinCamD V3.05N or earlier for use with pulsed lasers requires a firmware upgrade & full software upgrade.
Running Ver. 5.00F3 or earlier? Contact DataRay for a firmware upgrade.
Problems? Download and read Software Installation and follow all steps carefully.

 6.00P2 full version
 iDataRay600P2.exe



 

Old DLL Version 3.06R of the software
Most recent. Does not incoporporate major upgrades introduced since Q3 2002.
Ver. 3.06R
DataRay306R.exe 7.0 MB
7 July '03
 
BeamScope-P3 & -P5 (Previous generation products)
Link to: Windows Compatibility
X-Y Profiling, M2, Scanning Pinhole Imaging
See above for software for BeamScope-P7, the current product, launched Q2 2002.
Ver 5.3G Addressed various small issues.  

Ver. 5.3G
 BSDisk1.zip 830 kB
BSDisk2.zip 830 kB

Ver. 5.3G Upgrade only
BSexe.zip 230 kB
  

10 May '01

WinCam-PCI (Previous generation product)
Link to: Windows Compatibility
(Previous generation product) Camera based Beam Imaging
See above for software for WinCamD, the current product, launched Q3 2001.
Ver 3.05J clears up printer scaling when using the Inclusion Region  


WCDisk1.zip 1 MB
WCDisk2.zip 320 kB

Ver. 3.05J Upgrade only
WCexe.zip 330 kB

10 Jan '01


Warning!    If you download via a company server which has a cache turned on,
   and       you have already downloaded a previous version of a file with the same name,
   then      the caching routine may ignore file updates where the name has not changed,
   unless   it also checks file revision dates on downloadable files.
   Either   ensure that the caching routine verifies file dates,
   or         persuade your IT people to implement the file date check function on the server.

Windows 2000 Service Pack 3. Warning update, 8 Aug. 2002:
This warning applies ONLY to software Versions prior to 5.00A.
You may fix your version as outlined below. Alternatively, upgrade using the latest version of the software, above.

Older versions of the windrvr.sys file (used to communicate with the PCI card) are incompatible with Windows 2000 Service Pack 3, released by MicroSoft on 1 Aug. 2002. Do not install SP3 for W2K until you have upgraded the windrvr.sys file or loaded the latest version of the software.
Unzip the windrvr.sys file to c:\Program files\DataRay, replacing the previous version.
Also replace the file in the c:\WINNT\system32\drivers file.
Reboot.
  
If this warning is too late, you have already installed W2K SP3, & your machine will not boot:
1) Power off the PC, remove any DataRay cards and restart.
2) If it restarts, replace windrvr.sys as detailed above. Then power it down, reinsert the DataRay PCI cards and restart.
3) If it does not restart after stage 1) or 2), refer to www.jungo.com/support/tech_docs/td108.html?jungonl0802.
     As and if necessary, call in your PC support staff.
   
Obtain additional technical support at (303) 543-8235 or support@dataray.com.